Just how do you feel with regards to Tools You Need to Install a New Bathtub ?
Mounting a bath tub isn't exactly brain surgery, however it does need strong plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old bathtub with a brand-new one is additionally a reasonably difficult project. If the old bathtub is conveniently accessible, the project can move quickly; if you need to open a wall surface to eliminate the old tub and position the brand-new bath tub, the task is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly need a helper to move out the old bathtub as well as embeded in the new one. See to it you have certified on your own for the job as well as fit trying it. As opposed to hiring a service provider to take control of a halfway-completed project, it is better to think about utilizing one prior to you start. Possibilities are you may need a professional plumber to make tube connections.
This write-up will certainly assist you set up a new bathtub in your bathroom if you have actually currently purchased a new bathtub and don't require to alter the arrangement of your previous water system pipelines.
Your tools and also material checklist ought to make up the following:
Preparing for the Installment
To start with, the supporting framework supplied with the bathroom should be fitted (if required) according to the maker's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to see to it that if the faucet comes with a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets system to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of the two taps using 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its final placement.
Removing Old Touches
If you require to change old taps with new ones as a part of your installment, then the first thing you must do is separate the water supply. After doing so, turn on the taps to drain any water remaining in the system. The process of eliminating the existing taps can be quite problematic due to the limited accessibility that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly originate from the pipelines. When the supply pipelines have been eliminated, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from transforming throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any type of old sealing substance.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Utilizing both wooden boards under its feet, put the tub in the needed placement. The wood boards are handy in equally spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 little points.
The following objective is to make sure that the tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bath tub up until the level reads degree.
To mount taps, fit all-time low of the furthest flexible faucet port to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Turn on the supply of water and also inspect all joints and also brand-new pipework for leaks and also tighten them if necessary. Fill up the bath tub and likewise examine the overflow electrical outlet and the regular electrical outlet for leakages.
Lastly, deal with the bath paneling as defined in the producer's user's manual. Tiling and also sealing around the bath tub ought to wait till the bathtub has been utilized at the very least once as this will settle it into its final position.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly require reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin ensuring that the washers remain in location between the faucet as well as the sink. Secure the tap in position with the producer provided backnut. Once the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet ports. The previous type ought to be attached to the tap finishes initially, tightening up only by hand. The supply pipelines can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bath fulfills the tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to fracture a rigid seal, creating the water to penetrate the wall between the bathroom and the tiling, causing issues with moisture as well as possible leaks to the ceiling below.
You can select from a range of coloured sealants to blend in your components and also installations. They are offered in tubes and also cartridges, and also are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill the bath tub with water before sealing, to permit the motion experienced when the bathtub remains in use. The sealant can split fairly very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently available on the market. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed reading our section about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you for finding the time to read through our blog. Enjoyed our write up? Please share it. Help another person locate it. I am grateful for your time. Visit us again soon.
Professional touch awaits.